-28%

1.2m Long Beech Butcher Block Edging Strip for 30mm or 40mm Kitchen Worktops

Original price was: £18.00.Current price is: £12.99.

Share:

Beech Butcher Block Edging Strip for 30mm and 40mm Worktops

This beech butcher block edging strip covers the cut end of a Beech Butcher Block kitchen worktop, so the end of the run is finished in the same colour as the surface. It is 1.2 metres (1200mm) long and made for 30mm or 40mm worktops, as its title says.

The listing describes it as designed for easy DIY fitting, protecting the worktop edge from knocks, moisture and wear, and suitable for laminate and wood worktops. The photos show three Beech Butcher Block strips and the Beech Butcher Block colour swatch.

Beech Butcher Block Edging Strip, view 1

Key features of the beech butcher block edging strip

  • Colour: Beech Butcher Block, light beech wood-block effect
  • Length: 1.2m (1200mm)
  • Suits: 30mm and 40mm kitchen worktops
  • Use: covering exposed, cut worktop ends
  • Worktops: laminate and wood, as the listing states
  • Quantity: 1 strip

Beech Butcher Block Edging Strip, view 2

What an edging strip does

When a worktop is cut to length, the cut end shows the raw core of the board. An edging strip covers that end with a strip in the worktop colour, so the end of the run looks as finished as the front edge. The beech butcher block edging strip does exactly that for Beech Butcher Block worktops, and it also helps protect the cut end from knocks and moisture, as the listing says.

The Beech Butcher Block colour

Beech Butcher Block has the look of a traditional butcher block worktop made from strips of light beech, with warm honey-coloured staves running along its length. It brings the warmth of wood to a kitchen without the oiling that a real timber top needs, and it suits cream, white, sage and grey units in country, shaker and modern kitchens.

The photos show three Beech Butcher Block strips and the Beech Butcher Block colour swatch.

1.2m long, for 30mm and 40mm worktops

Each strip is 1.2 metres (1200mm) long and, as its title says, made for 30mm or 40mm kitchen worktops. One strip covers both ends of a standard 600mm deep worktop with length to spare, or the end of a deeper breakfast bar. Trim the beech butcher block edging strip to width and length for a neat fit on either thickness.

Where edging strips are needed

Edging strips are used wherever the end of a worktop is on show: at the end of a run beside a door, next to a tall fridge or oven housing that is set back, at the end of a breakfast bar or peninsula, and on any worktop that is cut short in the middle of a room. Count every visible end before ordering, and order a beech butcher block edging strip for each.

Preparing the worktop end

Cut the worktop end straight and square with a fine-toothed blade, then sand it lightly so it is flat and free of dust and loose chips. The end must be clean and dry. Seal the cut end first if your worktop maker recommends it, and let the sealant dry before fitting the beech butcher block edging strip.

Fitting the strip

Follow the fitting instructions that come with the strip and the adhesive you use. In general, cut the strip a little longer and wider than the worktop end, fix it in place, press it firmly along its whole length, and leave it to bond before trimming. The listing describes the beech butcher block edging strip as designed for easy DIY fitting.

Trimming flush

Once the strip has bonded, trim the overhang flush with the top and front of the worktop. Use a fine file, a sanding block or an edge trimmer, always working towards the worktop so you do not lift the strip. Finish with a light sanding of the edges so the beech butcher block edging strip sits smoothly against the worktop surface.

Rounded and square fronts

Where the worktop has a rounded front edge, the strip needs shaping at the front corner to follow the curve. Mark the curve on the back of the strip using the worktop as a template, trim it close with a sharp knife or fine saw, and finish with a file. Take your time here; a neat corner makes the beech butcher block edging strip look factory-fitted.

Protecting against water

A cut worktop end is vulnerable to water, especially near a sink, kettle or dishwasher. Sealing the end and covering it with an edging strip keeps moisture away from the core. Wipe up spills promptly around the ends, and check the beech butcher block edging strip occasionally near the sink to make sure it is still tight.

Matching the worktop

The strip is made to match the Beech Butcher Block worktop colour. Browse our worktops for the matching Beech Butcher Block worktops and breakfast bars, and order the beech butcher block edging strip at the same time so everything arrives together.

Matching upstands

Finish the back edge of the worktop with a matching upstand where the range has one, and the whole worktop is colour-matched on every visible edge. Browse our upstands to complete the look alongside the beech butcher block edging strip.

Tools you will need

A tape measure, pencil, fine-toothed saw, sanding block and fine file, a sharp knife, the adhesive you have chosen, a clean cloth and some masking tape will cover most jobs. A small roller or a block of wood wrapped in cloth helps press the beech butcher block edging strip down evenly while it bonds.

Common mistakes

The most common problems are fitting onto a dusty or damp end, not pressing the strip down along its whole length, and trimming before the adhesive has bonded. Clean the end, press firmly, wait, and trim towards the worktop, and the beech butcher block edging strip will stay in place for years.

Cleaning and care

Wipe the strip with a soft cloth and warm, mildly soapy water, then dry it. The listing says it is easy to clean and maintain. Avoid scouring pads and harsh solvents, which can dull the surface or weaken the bond, and keep hot pans and appliances away from the beech butcher block edging strip at the end of the worktop.

Breakfast bars and islands

Breakfast bars, peninsulas and islands often have two or more visible ends, and they are the ends people see first when they walk into the kitchen. A colour-matched beech butcher block edging strip on each end makes a bar or island look like a solid piece, rather than a cut board.

How many strips to order

Count each visible worktop end and allow one strip per end, or one strip for two ends on standard 600mm deep worktops if you are confident with the cutting. Order one spare: it is useful if a cut goes wrong, and for matching colours later. Order every beech butcher block edging strip at the same time so the colour is consistent.

Repairing a damaged end

If an existing worktop end has been chipped or has swollen slightly from water, cut back to sound material if you can, sand it flat, seal it, and fit a new strip. A fresh beech butcher block edging strip can make a tired worktop end look new again without replacing the whole worktop.

Worktop joints and ends

Edging strips are for exposed ends, not for joints between two worktops. Where two worktops meet, use a joint strip, a mitre joint or worktop bolts, and seal the joint. Keep the beech butcher block edging strip for the ends where the cut face would otherwise show.

Laminate and wood worktops

The listing states that the strip suits various worktop materials, including laminate and wood. Whatever the worktop, the end must be clean, flat and dry for a good bond, and the adhesive must suit both the strip and the worktop. Test on an offcut first if you are unsure.

A quick kitchen fix

Worn or missing end strips make a kitchen look tired. Replacing them takes very little time and money, and it is one of the simplest ways to smarten up an older kitchen. A new beech butcher block edging strip on each end, a fresh silicone line along the back and clean cupboard doors make a big difference.

Utility rooms and other spaces

Worktops in utility rooms, laundry areas, home offices and garages have exposed ends too. The same strip finishes them neatly and protects the cut ends from knocks and damp, so use a beech butcher block edging strip wherever a worktop end is on show.

Getting a neat finish

The difference between a home job and a professional one is usually in the edges. Cut accurately, keep the strip slightly oversize, press it down firmly and trim with care, finishing with a light sanding. Run a finger along the trimmed edge: it should feel smooth, with no ridge where the strip meets the worktop.

Fitting order

Fit the worktops first, cut and seal the ends, then fit the edging strips before the upstands and sink. That way the strips are trimmed flush with the worktop before anything else sits against them. Leave the strips to bond fully before you load the worktop or wipe it with water.

Safety when cutting

Wear eye protection when cutting and sanding, and a dust mask in a confined space. Clamp the worktop or strip firmly before cutting so it cannot move, keep fingers well away from blades, and unplug power tools before changing blades or clearing offcuts.

Keeping the colour consistent

Edging strips, worktops and upstands are made to match, but colours can vary slightly between batches. Keep all the pieces for one kitchen together, and lay the strip against the worktop before fitting to check it matches in your lighting. If a strip will sit next to a sunny window, check it in daylight too.

Measuring the worktop end

Measure the depth of the worktop from the back edge to the front, and its thickness, at the exact end you will cover. Worktops are not always perfectly square after cutting, so measure at both the top and the bottom of the end. Cut the strip a few millimetres longer and wider than your measurements, and the overhang can be trimmed back to a perfect fit once the strip has bonded.

Write the measurements on a piece of masking tape stuck to each beech butcher block edging strip, so it goes on the end it was cut for.

Choosing an adhesive

The listing does not say how the strip is fixed, so choose an adhesive that suits both the strip and the worktop, and read its instructions before you start. Contact adhesives are applied to both surfaces and left to go tacky before pressing together; other adhesives need clamping while they set. Whatever you use, apply it evenly to the whole surface so there are no dry spots that could lift later.

End panels and tall units

Where a worktop finishes against a tall unit, an end panel or a wall, the end may be hidden and need no strip. Where it stops short, leaving a gap, or where a tall unit is set back from the worktop front, the end shows and needs covering. Stand where people will see the kitchen from, at the door and at the table, and check which worktop ends are really on view before you order.

Corners and curves

Edging strips are made for straight ends. On a curved or angled worktop end, the strip can be bent gently round a large curve if it is flexible enough, but tight curves and sharp corners need separate pieces cut and joined neatly. Cut the joins at a slight angle, and keep the join line where it is least noticeable, such as at the back of the worktop.

Edges near the hob and oven

Heat can soften some adhesives and mark worktop surfaces. Avoid finishing a worktop with an exposed end right beside a hob or oven where possible, and leave the gaps the appliance makers recommend. If an end does sit near a heat source, check the strip from time to time and re-fix it if the bond has loosened.

Edges near the sink and dishwasher

The area round the sink and dishwasher is the wettest part of the kitchen. If a worktop end sits close to them, seal the cut end thoroughly before fitting the strip, press the strip down well along its full length, and run a thin line of clear silicone along the bottom edge if the end is near the floor where water could collect.

Older kitchens

Many older kitchens have worktop ends that were never finished, or where the original strips have lifted or broken away. Peel off any loose old strip, scrape off the old adhesive, sand the end flat and clean, and fit a new beech butcher block edging strip. It is one of the quickest jobs in a kitchen refresh, and the result is noticeable straight away.

Storing strips before fitting

Keep edging strips flat, dry and at room temperature until you fit them. Strips stored in a cold garage or van can be stiff and less willing to bond, so bring them indoors a day before fitting. Keep them in their packaging until needed, so the decorative face is not scratched.

When to call a fitter

Fitting an edging strip is a small job that most people can do with care. If your worktops are being fitted by a kitchen fitter, ask them to fit the strips at the same time, as they will have the trimming tools to hand. For a single end on an existing worktop, a careful DIY fit is usually all it needs.

Checking the finished edge

When the strip is trimmed, look along the worktop from the end and from the front. The beech butcher block edging strip should sit flush with the top surface, with no lip to catch a cloth, and the front corner should follow the shape of the worktop edge. Run a damp cloth over it to check nothing catches, then leave it to settle before heavy use.

Small details, big difference

Kitchens are judged on their details. Neat silicone lines, doors that line up, handles that match and finished worktop ends all add up to a kitchen that looks well made. An exposed, raw worktop end is one of the first things people notice, and one of the easiest to put right. A colour-matched strip on every end is a small cost for a finish that lasts for years.

Before you start

Read the adhesive instructions, check the room temperature they ask for, and make sure you have everything to hand. Clear the area around the worktop end and protect the floor from dust. With everything ready, each strip takes only a few minutes to fit.

At a glance

  • Beech Butcher Block Edging Strip
  • 1200mm long
  • For 30mm and 40mm worktops
  • Matches Beech Butcher Block worktops
  • Easy DIY fitting
  • Protects cut ends

Beech Butcher Block Edging Strip questions

How long is it? 1.2 metres (1200mm).

Which worktops does it suit? 30mm and 40mm kitchen worktops, including laminate and wood worktops.

Does it match the worktop? It is made in the Beech Butcher Block decor, to match Beech Butcher Block worktops.

Can I trim it? Yes. Fit it slightly oversize and trim it flush with a fine file or sanding block.

Is it for joints between worktops? No. It covers exposed ends; use a joint strip or mitre for joints.

How many do I need? One per exposed worktop end; one strip can cover two ends of a 600mm deep worktop.

How do I clean the beech butcher block edging strip? Wipe with a soft cloth and warm, mildly soapy water, then dry.

Looking for more like this edging strip? Browse the full Edging Strips collection or the rest of the Kitchen Worktops shop. To learn more, see this overview of edge banding.

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.