-9%

Misty Peak Marble Breakfast Bar 40mm x 1500mm x 900mm

Original price was: £169.00.Current price is: £152.99.

Share:

Misty Peak Marble Bar 40mm x 1500mm

This misty peak marble bar 40mm x 1500mm brings a white marble effect with soft grey veining finish to the kitchen in a 1500mm x 900mm piece, 40mm thick. The front edge has a smooth, rounded wrap round profile, as the profile drawing in the photos shows, so there is no sharp corner to catch hips, hands or cloths.

Misty Peak Marble has the look of polished white marble, with soft grey veins drifting across a bright white background. It gives a kitchen a light, airy and elegant feel, and it suits white, grey, sage and navy units, brass or chrome handles, and both modern and classic styles. The marble look brings luxury without the weight, cost and upkeep of real stone.

Misty Peak Marble Bar 40mm x 1500mm, view 1

Key features of the misty peak marble bar 40mm x 1500mm

  • Colour: Misty Peak Marble, white marble effect with soft grey veining
  • Thickness: 40mm
  • Length: 1500mm (1.5m)
  • Depth: 900mm
  • Edge: rounded, modern wrap round profile
  • Use: breakfast bar, peninsula or island top
  • Quantity: 1 piece

Misty Peak Marble Bar 40mm x 1500mm, view 2

The Misty Peak Marble finish

Before ordering, compare the colour photos with your cabinet doors and floor in natural daylight: worktops look different under warm artificial light. The misty peak marble bar 40mm x 1500mm pattern runs along the length of the piece, so plan any joints and cut-outs where the pattern will line up neatly.

Misty Peak Marble Bar 40mm x 1500mm, view 3

Choosing the size

At 1500mm long and 900mm deep, the breakfast bar is deeper than a standard 600mm worktop, which leaves room for an overhang where stools tuck underneath, or a generous peninsula or island top. The 40mm thickness gives a solid, chunky edge.

Measure each run from the wall to the end of the last unit, add a little extra for trimming, and decide where any joints will fall, ideally away from the sink.

Misty Peak Marble Bar 40mm x 1500mm, view 4

Cutting and fitting

Dry-fit the misty peak marble bar 40mm x 1500mm on the units before fixing anything. Mark cuts carefully, protect the cutting line with masking tape and cut from the decorative face with a fine-toothed blade so the edge stays clean. Support both sides of the cut so the piece does not drop or chip at the end of the cut.

Fix worktops to the base units from underneath with brackets or screws that are shorter than the worktop is thick, and check everything is level along the run before fixing.

Sealing edges and cut-outs

Water getting into cut edges and joints is the most common cause of worktop damage, so seal every cut edge, joint and sink or hob cut-out with a suitable sealant before fitting, following the instructions supplied with your sealant. Finish the back edge against the wall with an upstand or a bead of silicone, and use matching edging strips on exposed ends. Browse our upstands and edging strips to finish the job.

Everyday care

Wipe the surface with a soft cloth and warm water with a little mild detergent, then dry it. Mop up spills straight away, especially around the sink and along joints. Avoid scouring pads, abrasive creams and harsh solvents, which can dull the finish.

Always use a chopping board for knives and a trivet or pan stand under hot pans, kettles and slow cookers rather than putting them straight onto the surface. Browse our chopping boards for a matching set.

Joining two lengths

Where two worktops meet in a corner or along a long run, the joint needs to be tight and sealed. Many fitters use a worktop joint strip, which covers the cut ends neatly, or a mason’s mitre cut with a jig for a seamless look. Whichever you choose, seal the joint before the pieces are pulled together, wipe away any excess straight away, and plan joints away from the sink where water collects. A single long piece of misty peak marble bar 40mm x 1500mm avoids joints altogether on a straight run.

Sink and hob cut-outs

Use the template supplied with your sink or hob to mark the cut-out, drill a starting hole in each corner and cut with a jigsaw fitted with a fine blade, supporting the waste piece so it does not break away and chip the surface. Seal the raw edges of the cut-out thoroughly before fitting the sink or hob, and use the seal supplied with the appliance. Leave the gap around a hob that the hob maker recommends.

30mm or 40mm thick?

Worktop thickness changes the look of a kitchen. A 40mm edge has a classic, chunky presence that suits traditional and shaker kitchens, while a 30mm edge looks slimmer and more contemporary. The misty peak marble bar 40mm x 1500mm is 40mm thick; keep the same thickness across a kitchen so joints and upstands line up.

Planning a kitchen refresh

Changing the worktops is one of the quickest ways to transform a kitchen without replacing the units. Pair a new white marble effect with soft grey veining surface with fresh handles, a new sink or tap and matching upstands, and the whole room looks updated. Order all lengths in one go so every piece of the misty peak marble bar 40mm x 1500mm range comes from the same batch and matches.

At a glance

  • Misty Peak Marble Bar 40mm x 1500mm
  • white marble effect with soft grey veining finish
  • 40mm thick, 900mm deep
  • Rounded wrap round front edge
  • Room for a seating overhang
  • Seal all cut edges when fitting

Misty Peak Marble Bar 40mm x 1500mm questions

What size is it? 40mm thick, 1500mm long and 900mm deep.

What does the edge look like? A smooth, rounded wrap round front edge, as shown in the profile photo.

Can I cut it to size? Yes. Cut it with a fine-toothed blade from the decorative face, and seal the cut edges before fitting.

Do I need to seal it? Seal every cut edge, joint and cut-out so water cannot get in.

Can I put hot pans on it? Use a trivet or pan stand for hot pans, kettles and slow cookers.

How do I clean the misty peak marble bar 40mm x 1500mm? Wipe with a soft cloth and warm, mildly soapy water, then dry. Avoid abrasive cleaners.

What finishes the back edge? An upstand or a bead of silicone against the wall, with edging strips on exposed ends.

Looking for more like this worktop? Browse the full Worktops collection or the rest of the Kitchen Worktops shop. To learn more, see this overview of countertops.

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.